Panamax M4315 PRO 15A Bluebolt Power Conditioner

Panamax M4315 PRO 15A Bluebolt Power Conditioner
Not Ready to ship

No, this item is not in stock!

This item is no longer available.


You will receive: 1 Panamax M4315 PRO 15A BlueBOLT Power Conditioner
Panamax M4315-PRO

Advanced 15 amp power controller with top of the line Linear Noise Filtration, Automatic Voltage Monitoring and catastrophic surge protection.The M4315-PRO features Panamax's revolutionary AVM (Automatic Voltage Monitoring) circuit, and our exclusive Linear Filtering Technology (LiFT). Together, these technologies comprise precisely what our customers have come to expect from Panamax: uncompromised AC protection and purification. Outlets: all eight (8) rear panel outlets are separately controlled. They are grouped into four (4) filter-isolated banks. BlueBOLT is included, providing secure, hosted IP system control and monitoring for the M4315-PRO.1 RU 15AMP 8 BlueBOLT Programmable Outlets w/Auto Reset, 10Ft IEC CordIf you are looking for a vertically mounted solution, try the VT4315-PRO.


• Power Management with Control System Interactive Functionality.
• 15 Amp Capacity M4315-PRO
• 8 Individually Controllable Rear Panel Outlets
• Fully Programmable
• TCP/IP (BlueBOLT) Installed
• RS-232 Card (Included, not installed)
• Linear Filtration with 3 Isolated LiFT Filter Banks, 76db (5 kHz - 250 kHz), 46 db (250 kHz - 1 MHz)
• One Isolated Filter Bank for High Current Devices, 60db (5 kHz - 450 kHz), 46 db (450 kHz - 1 MHz)
• Front Panel Circuit Breaker
• Removable Front Rack Ears
• 12 Volt Input Triggering
• Detachable 10 ft. Power Cord
• AVM & Protect-or-Disconnect Circuitry
• Eight Fully Controllable/Programmable Outlets via RS-232C or BlueBOLT
• Two Front Panel Programmable Reboot Buttons
• IP Control with BlueBOLT-CV1 and RS-232C Cards
• Sleek New Design Including Volt/Amp Meter, Outlet Status and Warning LED’s
• Removable Rack Ears (Included)

Features Descriptions

Remote Power Management technology provides secure, hosted IP (Internet Protocol) system control. With BlueBOLT, custom electronics installers, integrators and end-users can remotely monitor and control power to home theater equipment by accessing power management components from anywhere in the world. From simple system reboots to comprehensive monitoring of power status, BlueBOLT provides the power to control complex A/V systems from their most fundamental level: their power source (M4315-PRO).

RS232 Communication Interface Card:

For custom configuration and/or home automation control. (Included, not installed)

LiFT Technology EMI/RFI Noise Filtration

Your audio/video components are constantly being bombarded by electromagneticinterference (EMI) and radio frequency interference (RFI) through their AC power source. This contaminated power can affect audio/video equipment and will degrade the overall performance of your entire system. Common symptoms of contaminated power include loss of picture detail, dull colors, pops, hisses,hums and visual artifacts.

Automatic Over & Under Voltage Protection (AVM)

Panamax’s patented power monitoring circuitry constantly monitors the AC line voltage for unsafe voltage conditions such as momentary spikes or prolonged over-voltages and under-voltages (brownouts). These unsafe conditions pose a very dangerous threat to all electronic equipment within the home. If the M4315-PRO senses an unsafe power condition, it will automatically disconnect your equipment from the power to protect equipment from damage. Once the voltage returns to a safe level, the M4315-PRO will automatically reconnect the power.When subjected to a 6,000V (open circuit voltage) / 3,000A (short circuit current)surge, the M4315-PRO limits its voltage output to less than 330V peak,UL’s lowest rating.If the magnitude of the surge is greater than the capacity of the surge protection components, the M4315-PRO’s Protect or Disconnect Circuitry will disconnect your equipment in order to protect it. The M4315-PRO will need to be repaired or replaced by Panamax if this occurs within the product’s 3 year warranty.

4 Isolated Outlet Banks

The M4315-PRO is designed to provide noise isolation between the outlet banks so that any noise created by A/V components plugged into the M4315-PRO cannot contaminate the power going to equipment plugged into the other outlet banks of the M4315-PRO.

Sequential Startup/Shutdown:

Complex audio/video systems may be susceptible to voltage transients generated internally at start-up/shutdown if all of the equipment is powered on or off at the same time. This can cause speaker “thumps”, which are not only annoying,but can also damage the speakers and/or trip product circuit breakers. The M4315-PRO is designed to eliminate these transients by providing a “start-up” delay for the High-Current outlets and a “shut-down” delay for the Switched Outlet Banks. This minimizes inrush current issues by allowing the components plugged into the Switched Outlet Banks to power-up and stabilize before any amplifiers and powered subwoofers are turned on. This sequence is reversed during shut-down. The amplifiers and powered subwoofers turn off, their power supplies drain, and then the equipment plugged into the Switched Outlet Banks are turned off. Additionally, the start-up and shut-down delays can be adjusted for custom applications.

Voltage Sense Trigger:

The M4315-PRO voltage sense trigger input uses a standard 3.5mm (1/8”) mini-mono plug. This feature provides an ON/OFF trigger for the M4315-PRO using a Direct Current (DC) voltage signal. Many components such as preamplifiers and receivers have a DC trigger built in, and will transmit a constant power signal when turned on and in use. The presence of this power signal will turn on the M4315-PRO’s switched outlets. When the source component is turned off, the voltage trigger signal is also turned off, and the M4315-PRO’s shutdown sequence is initiated. An AC Adapter of the appropriate voltage (5-24 VDC) plugged into a switched outlet may also be used if a DC trigger is not built in.

Cable/Satellite/Antenna TV signal protection:

Coaxial protection circuits achieve optimum signal quality from our new coaxial protectors that have the smallest signal loss on the market - less than 0.5 db of attenuation from 0 Hz to 2.2 GHz. Our upgraded coaxial protection has been specifically designed to virtually eliminate signal loss. The clamping level of 75V will meet the demands of both cable and satellite voltage while minimizing exposure to damaging spikes and surges.

Telephone Line Protection:

Digital video recorders and satellite TV receivers require a telephone line connection for TV show scheduling and/or Pay-Per-View services. The M4315-PRO also provides surge protection for this line. One pair of RJ-11 telephone jacks is provided for this. The circuitry utilizes auto-resetting PTCRs and solid state SIDACtors for reliability and unsurpassed protection. The clamping level of the M4315-PRO’s telephone protector is 260 volts. This will allow typical ring voltage (90-130VAC) and operating battery voltage (-48DC) to pass through the circuit and still protect the modem in your satellite receiver from damage.Incoming tel line must be plugged into the IN Jack. Patch cord to the equipment must be plugged into OUT.

LAN Protection

Protection circuits for 10/100/1000 baseT Ethernet lines. 8 wire protection, 62V clamping.


• Line Voltage: 120V, 60Hz
• Isolated Banks: 2
• Voltage Regulation: No
• Total Outlets: 9 outlets
• High Current Outlets: 2 outlets
• Total Current Capacity: M4315-PRO 15 A (1800W) - M4320-PRO 20 A (2400W)
• Voltage Protection Rating (UL 1449 3rd Edition, 3,000A): 500V
• Protection Modes: L-N, L-G, N-G
• Initial Clamping Level: 200V Peak, 141V RMS
• Energy Dissipation: 2700 Joules
• Peak Impulse Current: 135,000 Amps
• Catastrophic Surge Circuit: Yes
• Thermal Fusing: Yes
• Auto-resetting Over-voltage shutoff: 134 VAC ± 2 VAC
• Auto-resetting Under-voltage shutoff: 100 VAC ± 2 VAC
• EMI/RFI Noise Filtration Banks 1, 2, 3: 76db, 5KHz - 250 kHz , Bank 4, High Current Outlets: 46 db, 250 KHz - 1 Mhz
• Clamping Level: 60 ± 5V
• Compatibility: 10/100/1000 BASE-T
• Jacks: RJ-45
• Wires Protected: 8-Wires
• Fuseless/Auto-resetting: Yes
• Clamping Level: 260V
• Capacitance: 30pf (approx.)
• Suppression Modes: Metallic & Longitudinal
• Connectors: RJ-11
• Lines Protected: 2-Wire, Pins 4 & 5
• HD 1080 i/p Ready: Yes
• Bidirectional: Yes
• Shielded: Yes
• Clamping Level: 75V
• Frequency Range: 0MHz - 2.2 GHz
• Insertion Loss: < 0.5 dB
• Connectors: Female “F”, Gold Plated
• Product Dimensions: L 12.25” x W 17” x H 1.75”
• Weight: 12 lbs.


  • UPC: 050616008594
  • EAN: 0050616008594
  • SKU: M4315-PRO

Write a review

Please login or register to review